- No display orders in Fix PCs usually trace back to a dead GPU, unseated RAM, or PSU power cables.
- Run the diagnostic tool first — it points to the failing component before you touch a screw.
- Always work at the workbench; repairs can't be completed on random counters.
- Screws and cables must be fully seated or the part won't register as installed.
- Finish every job with a passing benchmark test before returning the PC.
Why a Customer's PC Shows No Display
The no display repair ticket is one of the most common orders you'll handle in Fix PCs. A customer brings in a PC that powers on but shows nothing on the monitor, and it's your job to trace the fault. In most cases the culprit is one of a small group of components, so learning these patterns turns a slow job into a quick paycheck.
Dead GPU
- Most frequent cause of no display
- Diagnose, unscrew, swap in a replacement card
- Higher-tier GPUs boost the payout
Unseated RAM
- Loose memory blocks boot entirely
- Reseat sticks or swap faulty modules
- Cheapest fix in the game
PSU / Power Cables
- Disconnected PSU-to-motherboard power
- PSU switch flipped off
- Check connectors before swapping parts
Always use the diagnostic tool on the customer's PC before opening the case. The scan identifies the failing component, which saves you from pulling good parts and redoing the job later.
Fault Symptom Reference Table
Use this quick-reference table to match symptoms to the failing part. Memorizing these pairings dramatically speeds up your turnover rate and lets you stock the right components.
| Symptom | Likely Fault | Fix | Typical Cost |
|---|---|---|---|
| Powers on, no display | Dead GPU | Swap GPU, reconnect power cable | $$ |
| No power at all | PSU cable / switch | Reconnect PSU, flip switch | Free–$ |
| Boot loop / beep errors | Faulty RAM | Reseat or replace RAM stick | $ |
| Display but slow boot | Failing HDD | Upgrade to SSD | $–$$ |
| Benchmark fails randomly | Loose screws or cables | Re-seat everything and retest | Free |
A low-wattage PSU paired with high-end parts can fail the benchmark even when every component works. If the diagnostic comes back clean but the test still fails, check whether the power supply has enough headroom for the build.
Step-by-Step: Fixing a No Display Order
Follow this exact sequence for every no display ticket. The repair loop in Fix PCs rewards consistency: same steps, same order, faster each time.
Accept the Ticket and Locate the PC
Interact with the waiting customer to accept the repair ticket, then head to the shelf or counter where their PC is placed.
Run the Diagnostic Scan
Use the diagnostic tool on the PC. For no display orders, expect the scan to flag the GPU, RAM, or a power connection.
Move the PC to the Workbench
Carry the PC to your workbench and place it down. All disassembly and part swaps happen here — the bench is mandatory.
Open the Case and Remove the Faulty Part
Unscrew the side panel, then unscrew the failing component. Hold left-click on each screw and follow the on-screen motion. Unplug any attached power or data cables.
Install the Replacement
Grab the correct replacement from your parts inventory, screw it firmly into place, and reconnect every cable you detached.
Close Up and Run the Benchmark
Reattach the side panel, plug the PC in, and power it on. Run the benchmark — a pass confirms the fix; a fail means something is still loose.
Deliver and Collect Payment
Return the repaired PC to the customer to collect your Cash. Reinvest early earnings into better tools and a second workbench.
Keep your most-used parts (GPUs, RAM, PSUs) shelved within reach of the workbench. Fewer steps between diagnosis and install means more completed repairs per hour.
Common Sticking Points and Fixes
Even experienced technicians get stuck on no display orders. These are the situations new players hit most often, with the fix for each.
| Sticking Point | Cause | Fix |
|---|---|---|
| Part won't come out | Remaining screws or attached cable | Inspect for missed screws, unplug the power connector |
| PC won't power on | PSU not connected to motherboard | Reconnect the PSU cable, flip the PSU switch |
| Ticket won't complete | Wrong part tier installed | Compare installed parts against the ticket requirements |
| Benchmark fails repeatedly | Loose screws, cables, or weak PSU | Re-seat everything; upgrade PSU wattage |
| No cash for parts | Early-game economy | Take loose-cable jobs first or sell removed spares |
Some jobs require a specific part tier. Installing a cheap entry GPU where the ticket calls for a mid-range card means redoing the entire job — and paying for both parts.
No Display Repair Checklist
Before you hand any no display PC back to the customer, run through this checklist to guarantee a one-visit fix.
Before Returning the PC:
- Diagnostic scan confirms no remaining faults
- All screws fully tightened on the panel and part
- PSU connected to motherboard, switch flipped on
- All power and data cables fully seated
- Benchmark test passed with a green result
Invest in better tools before anything else — an upgraded screwdriver and diagnostic kit cut minutes off every single order, making it one of the best early-game returns in Fix PCs.
FAQ
Q: How do I fix no display in Fix PCs?
Accept the ticket, run the diagnostic tool to identify the fault (usually the GPU, RAM, or a power cable), bring the PC to your workbench, swap or reseat the faulty component, then pass the benchmark test before returning it to the customer.
Q: Why won't the part come out when I unscrew it?
Check for remaining screws or an attached power cable. Some components, especially GPUs and PSUs, have extra connectors that must be unplugged before the part detaches.
Q: Why does the benchmark still fail after I replaced the GPU?
A failing benchmark usually means something is loose — re-check screws and cables — or the PSU doesn't have enough wattage for the parts installed. Low-wattage power supplies fail benchmarks with high-end components.
Q: What's the fastest way to make money fixing no display orders?
Memorize the symptom-to-fault pairings so diagnosis is instant, stock high-demand parts near the workbench, and take GPU-swap orders once you can afford replacements — they pay significantly more than loose-cable fixes.